#91 SR400Custom Report
06 model. With an immobilizer that is not suitable for customization, we have created a 70s chopper style with a high-year SR.
By modifying and reusing the Harley Springer and hanging the exhaust pipe under the frame, we have created a style that lifts the belly.
[ Overall Silhouette ]
• 8-inch over springer for Harley
• F19 / R16 inch wheels, seat rail drop, swing arm extended by 5cm
〇“THE SR TIMES” featured article is here
〇“CHOPPER JOURNAL” featured article is here
〇“BIKEBROSS Magazines” featured article is here

Custom List
FrontHandlebars, F forks, headlights, etc.
【Front Fork Area】
◯The front end is springerized. The new product “Harley ⇒ SR400/500 Neck Bearing Kit” is used to transplant a Harley springer.
◯By creating a link rod according to the neck angle and disk diameter, and changing its position, the fork smoothly bottoms out during braking. Even though it’s a springer, you can operate the brakes safely. It’s also safe during panic braking.
【Front Wheel】
◯Brakes and 19-inch wheels are also for Harley.
【Headlight】
◯The headlight is a “Mirror Corner Light” (discontinued) with two corner lights.
【Handle/Handle Area】
〇A narrow flat handle with a short clamp section. The riser is a 5-inch Paughco product.
“Amal type throttle holder, general purpose (for 7/8″)“
“Amal type slot wire 1100mm ’88~’08“
◯The controls are kept simple with mini switches and the like.
【Switch】
“Mini Turn Signal Switch Coupler On Kit (’85~00)”
〇Easy to install mini turn signal switch with coupler on
● It is newly installed by welding to the lower part of the stem, which is inconspicuous and easy to operate.
“MOTOR ROCK Decompression lever“
A decompression lever directly attached to the engine to simplify the area around the handle. (The one on the vehicle is an old model)
【Front Blinker】
“Small Bullet Turn Signal Chrome 4pcs SET General Purpose“
〇A classic among classics. A chopper-style blinker.
“SR400/500 Bottom Mount narrow blinker stay“
〇A stay to attach a 10mm blinker to the bottom of the frame.
【Speedometer】
“Mechanical Speedometer 60mm Black Panel 1:4“
〇Mounted on the left front side of the gasoline tank, which is inconspicuous and highly visible.
〇Used when extending the fork or relocating the meter.
CenterTank, oil tank, seat, step, muffler etc.
【Muffler】
“One-off Pipe Manufacturing Exhaust Pipe Flange Set”
〇A one-off upsweep muffler made using a convenient manufacturing kit for the mouthpiece at the root. A trumpet is attached to the end and used as a silencer.
【Step】
“Mid-High Control Parkerized for SR400/500“
〇This step kit is essential for 2%ER’s custom, which makes the riding posture cool and the position extremely less tiring.
【Seat】
◯With a one-off high-back seat, you will have a comfortable riding posture. Especially inside the seat, a backrest frame is installed so that the entire weight can be applied.
【Seat Rail】
◯ Seat rail processing that drops the seat straight without bending.
【Electrical Equipment】
◯ Especially in high-year models, it’s hard to fit electrical components, but we’ve neatly organized them under the seat. We plan to make an electrical box.
『IC blinker relay wide range specification』
〇 A wide-range blinker relay that can handle 1-150 watts without any problem, even with LED blinkers. It can also be used as a replacement for the original relay.
【Gasoline Tank Installation】
◯ The gas tank is a one-off peanut. It is safely mounted with three-point rubber.
“Welding nut non-through M8 2p“
〇 Drill a hole in the gasoline tank body and insert and weld. It’s non-penetrating, so it won’t leak. Used on both sides.
“Weld tab M size 4.5mm thickness 2p“
〇 Enlarge the hole diameter and change to a rubber mount specification to hold the non-penetrating nut. Used on both sides.
“Weld tab L size 4.5mm thick steel 2p“
〇 Used for the rear installation of the gas tank. This also enlarges the hole diameter and uses it as a rubber mount.
【Kick Pedal】
Install a kick pedal with a nice atmosphere. It will also make it easier to step on the kick.
【Carburetor】
◯The carb is a “Big Carb Kit” (discontinued). It will take your ride to the next level.
【Engine Area】
〇This is a filter kit needed when removing the original air cleaner.
【Drive System】
“Front sprocket SR400/500 428-19“
〇A durable replacement sprocket made of steel.
RearFenders, rear shocks, swingarms, etc.
【Rear Wheel】
“16″ Kit Steel Spoke SR400/500 Rear“
〇A kit that gives a powerful look with the same size as a typical Harley.
“Drilled plate torque rod SR400/500“
〇A drilled design torque rod to avoid interference with the widened tire.
【Rear Shock】
◯Lowered with a one-off rigid suspension. The swing arm has been extended by 5cm.
【Sissy Bar】
◯A one-off sissy bar made from a square bar. We made the decoration modest so that you won’t get tired of riding for a long time.
【Rear Fender】
◯The rear fender is also a one-off production. It’s a tough condition where the weight is applied on the heavily vibrating SR, and it also serves as a support for the sissy bar, but we have effectively reinforced the backside with suitable materials so that you can use it for a long time.
【Rear Blinker】
“Small Bullet Turn Signal Chrome 4pcs SET General Purpose“
〇A classic among classics. A chopper-style blinker.
“Weld tab S size 4.5mm thick steel 2p“
〇Welded onto a hardtail. Used as a blinker base.
【Drive System】
『Rear sprocket SR400/500 428-56 』
〇An affordable and durable replacement sprocket.
※Parts Reference may show similar products or products with additional processing.